6506> (enable) show config
This command shows non-default configurations only.
Use show config all to show both default and non-default config
.........
................
................
..............
..
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Thu Jan 4 2001, 08:27:22
!
#version 5.4(3)  #软件版本
!
set password $2$lnsk$mgJ84scE.A51hpr0Zbdfv/ #加密后的telnet密码
set enablepass $2$RFAC$BDgIVKdk3gl1RD4.DaNcu. #加密后的enable密码
!
#system
set system name  6506 #系统名称
!
#!
#vtp
set vtp domain _domain # VTP域名
set vtp passwd _password # VTP域密码
set vlan 1 name default type ethernet mtu 1500 said 100001 state #建立VLAN
set vlan 2 name vlan2 type ethernet mtu 1500 said 100002 state act
set vlan 3 name valn3 type ethernet mtu 1500 said 100003 state acti
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 st
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005
p ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 10
ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#ip
set interface sc0 1 10.1.1.253/255.255.255.0 10.1.1.255 #本交换机的IP地址
set ip route 0.0.0.0/0.0.0.0         10.1.1.254 #默认网关
set ip alias default         0.0.0.0  #设置ip对应的设备名，方便管理
set ip alias 6506            10.1.1.253 #用途如：ping 2620, telnet 3548_2a
set ip alias msfc            10.1.1.254
set ip alias 4912            10.1.1.252
set ip alias 2620            10.1.8.250
...

!

#set boot command

set boot config-register 0x102 #启动寄存器值及启动文件

set boot system flash bootflash:cat6000-sup.5-4-3.bin

!

#mls

set mls flow full #多层交换流类型

!

#security ACLs  #访问列表

clear security acl all

#server

set security acl ip server deny ip host 10.1.1.199 host 10.1.1.200

#

commit security acl all

!

# default port status is enable

!

!

#module 1 : 2-port 1000BaseX Supervisor #管理引擎（含2口千兆模块）

!

#module 2 : 8-port 1000BaseX Ethernet #8口千兆交换模块

set vlan 5    2/1 #指定端口2/1到vlan 5

set port name       2/1  gg #设置端口名称

set port name       2/2  cb

set port name       2/3  server1

set port name       2/4  server2

set port name       2/5  3548_2a

set udld enable 2/6-8  #未安装GBIC时激活检测

set trunk 2/1  off dot1q 1-1005 #设置2/1为运行802.1Q协议的干道，允许vlan

1-1005通过

set trunk 2/2  on dot1q 1-1005

set trunk 2/3  on dot1q 1-1005

set trunk 2/4  on dot1q 1-1005

set trunk 2/5  nonegotiate isl 1-1005

!

#module 3 : 8-port 1000BaseX Ethernet #8口千兆交换模块

set port name       3/4  3524_17a

set port name       3/5  3548_9b

set port name       3/6  3548_9a

set port name       3/7  3548_f4a

set port name       3/8  3548_12a

set udld enable 3/1-3

set trunk 3/1  on dot1q 1-1005

set trunk 3/4  nonegotiate isl 1-1005 #设置3/4为运行isl协议的干道，允许vlan

1-1005通过

set trunk 3/5  nonegotiate isl 1-1005

set trunk 3/6  nonegotiate isl 1-1005

set trunk 3/7  nonegotiate isl 1-1005

set trunk 3/8  nonegotiate isl 1-1005

!

#module 4 empty

!

#module 5 empty

!

#module 6 empty

!

#module 15 : 1-port Multilayer Switch Feature Card

set port name       15/1  msfc #路由、多层交换模块

!

#module 16 empty

end